top of page

Recycled Asphalt Driveways in NZ: What Millings Cost, How Long They Last and When to Pick Hot-Mix

sp8002
Oct 18
4 min read

Updated: Nov 10

A recycled asphalt driveway is old road asphalt, milled off and crushed to about 20 mm, then spread and compacted like gravel. In New Zealand it costs well under new hot-mix, which runs $250 to $400 per m² excluding GST in Auckland. It suits long rural or overflow driveways. It loosens and ruts on steep or busy ones.

What recycled asphalt actually is

When a road or carpark is resurfaced, a milling machine grinds off the top layer. That material is called RAP, short for reclaimed asphalt pavement. It is stone plus the old, aged bitumen that once held it together. Some goes back to the asphalt plant to be mixed into new hot-mix. The rest is sold by aggregate yards and cold-mix suppliers as millings or graded RAP, usually around 20 mm.

It is not the same as a bag of cold-mix, which carries added binder so it sticks in a hole. And it is not new hot-mix, which is laid with fresh bitumen at 140 to 160°C and rolled into a sealed, waterproof surface. A millings driveway is closer to a firm gravel driveway that sets a little harder over time.

What a millings driveway costs

There is no paving machine and no fresh binder, so the cost sits in four places: the material, delivery, grading and compaction. Material prices vary a lot with haul distance and order size, so ask any supplier for a delivered price per tonne, whether GST is included, and the grading.

To estimate quantity, plan on roughly 2 tonnes per m³ once compacted. At 100 mm deep that is about 0.2 tonnes per m². A 60 m² driveway needs about 6 m³, or roughly 12 tonnes. Soft or clay ground needs basecourse first, and that is often the bigger cost.

For comparison, a new hot-mix asphalt driveway in Auckland costs $250 to $400 per m² excluding GST, which puts 60 m² at $15,000 to $24,000. Our installation guide walks through the six stages of that build, from dig-out to the final roll.

How long it lasts, and why

The old bitumen in millings softens a little in summer heat. With compaction and traffic, some of it re-binds, and the surface firms up. It never closes as tight as hot-mix. Water still gets in, and loose stone still works free.

Expect three things over time: loose stone on turning areas where tyres scrub, ruts in the wheel paths, and potholes wherever water sits. Plan on top-ups and regrading, and plan on them more often on slopes. A well-built hot-mix driveway, by contrast, lasts 15 to 25 years with basic care.

Where millings work, and where they do not

Millings make sense on:

  • Long rural and lifestyle-block driveways, where sealing 200 m or more in hot-mix is hard to justify.

  • Overflow parking, boat and trailer pads, and farm tracks.

  • Temporary access during a build, before the final surface goes down.

  • A firm base under a future seal, if it is graded and compacted properly.

They are a poor fit for:

  • Steep driveways, where loose stone migrates downhill and water scours the surface.

  • Tight turning heads, and spots where cars turn their wheels while parked.

  • The first few metres outside the house, where stones and soft bitumen get tracked inside in summer.

  • Shared driveways and carparks with daily foot traffic, where a loose surface becomes a trip hazard and a liability question.

Drainage matters more than the material

Most millings driveways fail for the same reason gravel and asphalt do: water. If the surface has no fall, puddles soften the base and potholes follow. Build in a crossfall so water runs off, keep the edges clear so it can leave, and fix soft spots before you spread new material over them.

Can you seal over millings later?

Often, yes. Compacted millings can act as part of the base for a later chip seal or asphalt surface. The contractor will check the depth, how well it was compacted and whether the ground underneath is sound. If you are upgrading a shared lane, our guide to moving from gravel to asphalt covers the lifetime costs and how to split the bill.

Five questions to ask a millings supplier

  • What is the delivered price per tonne, and does it include GST?

  • What grading is it, and is it screened for oversize lumps?

  • Is it clean RAP, or mixed with concrete, brick or soil?

  • Is spreading and compaction included, or delivery only?

  • What depth do you recommend for my ground and the vehicles that use it?

If you want to know where the RAP itself comes from, we explain what happens to old asphalt after a repair.

When a patch is the better answer

Plenty of rural and suburban driveways are part sealed, part loose. If the sealed apron at the top or the section near the house has potholed, a fixed-price asphalt patch starts at $350 + GST, and a saw-cut hot-mix repair at $700. For a long driveway with a few bad spots, our note on rural driveway potholes covers which ones are worth a crew.

See our driveway repair service, or send a photo and we will tell you whether a patch, a full asphalt surface or a cheaper loose surface makes more sense for your driveway.

Want a sealed hot-mix surface instead of millings? See asphalt driveway cost in Auckland, per m², for new, resurfaced and replaced driveways.

 
 
 

Recent Posts

See All

Comments


bottom of page